Installing a rod holder on your kayak is a great way to keep your fishing rods easily accessible while you’re out on the water. Not only does this make it easier to access your rods, but it also keeps them safe and out of the way when they’re not in use.
The most asked question is how to install rod holder on kayak? The simplest way to install a rod holder on your kayak is using the Scotty Rod Bolt.
In this article, we’ll show you how to install a rod holder on your kayak in just a few simple steps.
Table of Contents
How To Install Rod Holder On Kayak?
The first thing you’ll need is a measuring tape and marker. Using these, you’ll want to measure out where you want to put your rod holder on the kayak.
It’s best to find a spot that’s behind any place you might have a seat so that it doesn’t block your ability to put a seat back in the kayak.
How To Attach The Rod Holder?
Once your rod holder has been installed on your kayak, you’re ready to place the rod holder in. There should be a rod holder that comes with the Scotty Rod Bolt kit.
Now it’s simply a matter of positioning your rod holder on top of where you’ve already drilled the hole, and lining up the holes so that they match up. Once all of this has been done, you can screw in your screws and bolts. Finally, you can place the end caps on to finish it off and make sure that your rod holder is ready to go!
It should take around 15 minutes for a beginner to install a rod holder on their kayak. If you rush through the process too quickly, there’s always a chance that something might not line up right or that you drilled the wrong hole. For this reason, it’s important to take your time and make sure that everything is done correctly.
After you’ve finished installing a rod holder on your kayak, you’ll be able to enjoy flying fishing with ease! Not only will you have easy access to your fishing rods while out on the water, but they’ll also stay safe and secure so you won’t have to worry about them sinking or getting damaged.
How Do You Determine Where To Place The Rod Holder On Your Kayak?
To determine where to place a rod holder on your kayak, you’ll want to look at the design of the kayak. Most kayaks have a bulkhead located near the stern of the boat.
If you’re looking for a good location to install a rod holder on your kayak, placing it behind the bulkhead is a great option. The rod holder should be a few inches above the waterline to ensure that it’s located in a good spot.
Once you have your measurements, you’ll need to make sure that they’re accurate. You don’t want to try to drill into the kayak only to find out later on that your measurements were wrong and you don’t have a good spot to drill.
Now you’ll need to use the measurements to determine where on the kayak you want to install your rod holder. You can mark this spot with a marker, but make sure that it’s not on the actual kayak material itself. You should place it somewhere on top of the material.
Next, you’ll need to drill the hole. It’s best to use a bit that is larger than what your screws and bolts will be, as well as having the longest length possible.
How Do You Clean The Rod Holder?
After using your rod holder for a while, dirt and grime might eventually build up on the unit. There are two ways to clean this up.
The first would be to use hot water and mild soap to wash down the rod holder. If there are any areas that are particularly dirty, you can always use a sponge or cloth to scrub them clean. The second option is to use alcohol to clean off the rod holder after it has been cooled off from being heated in hot water. This should remove any dirt and grime with ease. Once the rod holder has been cleaned, it’s ready to be put back on your kayak and used all over again!
Rod holders can get dirty after extensive use, so make sure that you clean them off every so often so they stay in good condition. Otherwise, there might be dirt and grime building up inside of your rod holder, which can cause problems down the line.
Conclusion
I hope this article was useful to you and answered your question of how to install rod holder on kayak? Now that you have your rod holder installed, you can pick out a fishing rod and go out to the water. Before you know it, you’ll be catching fish all over again! Just remember not to drop your rods overboard by accident.
FAQs
Q1. How long does it take to install a rod holder on your kayak?
It should take around 15 minutes for a beginner to install a rod holder on their kayak. If you rush through the process too quickly, there’s always a chance that something might not line up right or that you drilled the wrong hole.
Q2. Where should I install a rod holder on my kayak?
The best place to install a rod holder is on the kayak bulkhead. This way, your rods will be safe and secure when you’re out on the water.
Q3. How many rod holders should I install?
You should always install at least two-rod holders on your kayak. You never know when you might catch a big fish and need to use two rods at once.